General information

Avtopoilka for chickens do it yourself: making by technology

It is very important to provide chickens with enough clean and fresh water in a timely manner. Proper watering of chickens contributes to better processing of food and, consequently, increasing egg production in laying hens and increasing the mass and hens of meat breeds.

So that your birds always have clean and fresh water, you need to provide the house with a good drinker. The stores offer a large number of options, both for large farms and for private households.

It is clear with shops - I came, bought, installed. But what if there is a shortage of funds or the installation of purchased watering systems is simply impractical in view of a small herd? In this article we will look at several options for the manufacture of drinking bowls for smokers with their own hands. First of all, it is worth knowing what types of drinkers exist.

Simple open drinking containers

With simple drinkers it is clear - these are, as a rule, various basins, buckets, bowls, and bowls of plastic, galvanized or enameled iron.

Normal open containers should be used as drinkers for chickens. For example, for daily allowance you can put a saucer, in the center you can install a jar (so that they could not get into the container) and pour water. It is only necessary to ensure that they do not spill water - wet chickens can die from hypothermia.

Such drinkers are also called siphons. They are best suited for a small herd of chickens (about 10-12 heads). The principle of operation is quite simple - the water in the tank under pressure does not pour out, remaining in a vacuum. In general, it is easier to show how this drinker works.

Self-made vacuum drinker make quite simple. Water is poured into the container, then a saucer or a not-very-deep bowl is placed on the throat from above (for example, if a glass jar) on small wooden linings. After that, the container is turned over. At first some water will pour out, but then it will stop flowing out. Water will fill the bowl as it is consumed.

In the stores, by the way, you can find a special bowl for such a drinker. It has already been done deepening. It remains only to pour water into the container.

The disadvantage of such a watering system is that chickens can easily flip capacity. Therefore, the finished product can sometimes be a good option. They are inexpensive. Especially good option on the legs - it is more stable.

Photo: store vacuum drinking bowl

Such a system is difficult to assemble with your own hands, it is better to buy ready-made. The device of drinking troughs for chickens of this type is quite simple: on the basis a cup and a tongue with a valve are fixed. The tongue is located on the surface of the water and, as it descends, opens the valve, after which the water refills the cup to the required level.

Cup Drinker Sample

On top of the whole structure there is an adjusting screw that allows you to adjust the water level in the cup. Water flows through the nozzle to which the hose is connected. The other end of the hose is attached to a water tank.

Nipple

Such drinkers are also called drip. The principle of operation is simple: water enters the PVC pipe, in which nipples are screwed on at a certain distance. The water in this pipe comes from some container, for example, a plastic canister installed at a level above the structure. In fact, it turns out automatic drinking trough, it remains only to add water to the tank.

Nipple Drinker for Chicken

Dimensions drinkers for laying hens

The most important thing is that chickens should not get into the water, collect garbage and droppings there and at the same time could get free access to water.

The stores sell watering systems of a certain size, both for young animals and for adult birds. When making improvised drinkers, take into account the most important thing - chickens should not get into the water, collect garbage and droppings there and at the same time could get free access to the water.

Height drinking bowls for chickens

This parameter plays a very important role. Drinking bowls should be installed at a height that corresponds to the age of the bird. More on the photo:

Important! Before you collect the drinker and install it, keep in mind that chickens must reach for water. This allows the fluid to freely fall into the craw of the bird.

Winter drinkers for chickens. Some useful ideas and examples.

Heated drinkers are relevant for poultry houses that are not heated in winter. Water can freeze in a sub-zero temperature, and the chickens will remain without drinking.

You can, of course, bring the container after each meal and take it out with fresh, slightly warmed water to a new one. And this is the last option, if there is no electricity in the hen house (you can use various long-playing candles, but open fire in the house is very dangerous).

If there is electricity, we will show you how easy and simple it is to make a warm drinker yourself, and in several variants and in winter your hens will always be provided with a clean and fresh drink.

Winter drinking bowl do it yourself from a conventional light bulb

We found this idea on the website detikukuruzy.ru (photo from the same place). The principle is very simple: an ordinary incandescent lamp is installed in a metal box. A small hole is left at the top of the box. Further the drinking bowl is put on this box.

Heat from the bulb does not allow water to freeze. There is no way to make a box? Then here's a simpler version:

The lamp is mounted inside the cinder block (or foam block) and a drinking bowl is placed on it.

There is another option from a gift tin box. The principle is the same:

Chuck mounted

Drinking bowl for winter: a variant with a heating cable

For heating water in the drinker, you can use a heating cable, which is used when installing underfloor heating. This cable can be bought in hardware stores and they sell it there by the meter.

We wrap the bowl capacity (in the case of the photo above it is nipple), carefully isolate all the connections and connect to the network.

Heated vacuum drinker heating cable

Using a heating cable you can easily provide auto heating. To do this, buy a special unit that regulates the on and off. When the water cools to a certain temperature, the cable will begin to heat it to the optimum. This is a costly option, but applicable to a large population of chickens.

Non-freezing drinker

It sounds, of course, pathetic, because the water without heating still freezes at sub-zero temperatures, but still there is a way. It is especially relevant in cold weather, when the temperature outside is about -10 degrees.

The whole point is to fill the capacity of the drinker in another container of a larger size and fill the space between the two tanks with foam.

Homemade drinkers for chickens from the sewer pipe

From a plastic pipe that is used for sewage, you can make quite reliable and efficient wall drinkers yourself. Such devices are convenient not only for chickens, but also for their owners, as it is easy to pour and drain water in them, as well as to clean and wash.

How to make a homemade chicken drinker from a plastic pipe: a step by step description of the process

Draw a straight line along the entire length of the pipe. Holes will be cut through this line. Draw marker contour future holes. They should be oval about 20-30 cm long.

We drill a hole with a drill so that the file from the jigsaw can move freely in it.

Now it remains to fix the drinking bowl on the wall with fasteners. The ends of the pipe can be silenced or inserted into them branches, through which you can easily drain and pour water.

Suspended drinking bowl for chickens from the sewer pipe is ready.

Automatic water supply to drinkers from pipes

Homemade version, made of nipples, cork from the wine bottle, metal plate and wire.

Another idea to make the most automatic drinker for chickens. Used fittings from the cistern of the toilet. Water is supplied through a hose.

Plastic Bottle Drinkers

It is possible to make a pot for chickens in a few minutes from improvised means, for example, from plastic bottles.

The easiest option: in a five-liter butyl at a distance from the bottom we cut several round holes in a circle. Holes should be such that the bird can freely stick their heads and drink. The bottle can be hung or attached to the wall.

Water bottle from the usual 1.5-liter bottle:

Vacuum flask from plastic bottle and container:

Compliance with the rules for drinking water

For the most ordinary open drinking trough, it is allowed to use different containers; even a bucket and a kitchen bowl will do. But the owners with experience already know that this option is not effective due to the fact that chickens and chickens are not very neat and often crawl with their paws in a container with water. They pollute it, turn it over, therefore, it is unacceptable for the purposes of hygiene and economy.

Before you make an automatic drinker, it is recommended that you familiarize yourself with a number of important rules.:

  • the device must be sufficiently stable, for this purpose, it should be fixed to the wall,
  • Autodrinking should be designed according to the closed type so that the birds do not have the opportunity, there becomes paws,
  • water change takes about 3 days,
  • in winter, due to artificial heating does not occur water freezing in the water tank,
  • the water in such a tank is always clean, microbes do not appear,
  • Birds do not destroy the tank, and can safely use it.

This is one of the ideal conditions for the maintenance of chickens, which will greatly facilitate the task and reduce the waste of valuable time. Here, for example, poultry farms have long been equipped with nipple auto-drinkers.

Need to know! Feeding must be made food grade plasticand also not contain inside painting and fuel sludge.

Materials and tools for creating automated drinking trough

For the manufacture of their own hands do not need professional skills. It is enough to buy a bottle of 5-7 liters, such capacity can be bought with bottled water. You also need to find a small tub and a few clips - they will fix the filled container. Next, you need to flip the bottle, fasten on the clips and ready. The stores sell the same products with a similar design.

To date, especially nipple car drinkers. To build the device is a little more difficult and the following will be required:

  • marker,
  • device for threading,
  • several clamps,
  • water plug
  • plastic hose
  • pipe adapter
  • water tank
  • nipples 360 and 180 - the first will be needed for large individuals, the second for chickens,
  • drip pan,
  • screwdriver
  • drill,
  • Drinker fencing materials,
  • materials for fastening the device.

Big list necessary items It should not frighten, the whole construction is going to be extremely simple.

Making a nipple drinker with their own hands

The nipple type automatic drinkers, unlike their counterparts, are a model for automated water supply. Allowed use any capacity, even a bucket, the main condition is the dropper. One of the simplest nipple systems is such a scheme: nipples are mounted in a hanging bucket, they are located at the very bottom. The product can also supply water from the tank or be equipped with a flow system. To create avtogilki for birds will need basic plumbing knowledge, then the device quality will be level with with factory devices.

Manufacturing process

  1. First you need to prepare the workplace and tools.
  2. Further, holes are made in the pipe in 30 cm increments, but in the case of a pipe with a length of 100 cm, it is recommended to make no more than 5 holes. If you make more holes, then for chickens this will be a significant inconvenience.
  3. Holes should be drilled in the place where internal grooves are located, no further water leakage will occur. The hole diameter should be about 9 mm, nipples that are wound in advance with Teflon tape are installed there too - this will prevent water from flowing.
  4. Further, the stub is taken and put on the pipe and no matter which side. A hose is attached to the other edge; it must be fed to the water supply system.
  5. Attaching a drip catcher will create additional comfort for chickens.

Such auto-drinking is the best option, because different microorganisms do not form in the water due to the fact that water the device does not stagnate. The system is fully automated, which means that birds will have the opportunity to drink water at any time. There is a small minus - a relatively small waste of money, and an adult bird can break the design by jumping on the pipe, but the construction of a small fence will solve this problem. Simplified nipple option automated drinkers.

This is done like this.

  1. Any clean vessel is chosen.
  2. A hole is made at the bottom
  3. The nipple is mounted in a 9 mm hole
  4. The container is filled with water and fixed in a suspended state - the height is chosen so that the chickens can easily get to the trough.

Everything is very simple the device is ready!

Making a vacuum drinker with your own hands

For the device used glass jars of different size, the water from the inverted tank gradually flows into the bowl, in which the container is installed. Fluid retention occurs due to pressure in the can and at the top of the bowl. It is done this way - as the water is removed from the bowl, air flows in an inverted capacity in a certain amount and, accordingly, water flows out as much as was consumed by the chickens. The bank should be well secured and give the design maximum stiffness. Chickens are rather curious and restless, so they can easily break the entire system and turn over the capacity.

Hit is necessary for the construction:

  • make a gap
  • find a jar
  • prepare clean water
  • find a bowl.

Vacuum Plastic Car Drinker - it is done very simply. It is important that the rim of the bowl be rounded or rubber trimmed so that chickens cannot injure the neck.

Manufacturing process

  1. First, a high plastic basin is taken so that the level of the board height does not become higher than the level of the chicken neck.
  2. Further, holes are made in the bottle at a height of 15 cm from the bottom, then the full container should be placed in the basin. After that, the water will begin to drain and flatten out with the hole, perhaps a little higher.
  3. When water is consumed, the level in the tank decreases and refills.em missing amount in the pelvis. This is done by entering the air bubble, which distributes the pressure. A bottle of 5 liters will provide about 10 chickens with water.

Vacuum drinker of 2 bottles - The device is also easy to make, and the materials are right at hand. Manufacturing process

  1. Initially selected 2 bottles with stoppers for 5 and 8 liters.
  2. Further, a bowl is cut from one large container to a height of 15 cm.
  3. Then the two plugs are connected, and the bottle is turned over.
  4. A hole is made in the vessel wall to a height below the level of the bowl.
  5. It is necessary to pour water into the bottle and screw the cork together with the bowl.
  6. The hole should be covered with a finger, and then set the device to the wall with the help of derzhak.
  7. At the end of the finger is removed, and the water begins to flow into the saucer, creating a vacuum.

Vacuum Trough Drinker - the product is placed on the level of the back of the bird, in which case they will not be able to get there with their paws.

Manufacturing process

  1. A plastic pipe is being prepared.
  2. The knife is taken and heated to a hot state.
  3. Next, cut holes with a hot knife.
  4. Then the edges are muffled and water is connected to one end through a water main.
  5. At the end, a drainage valve is constructed, which performs the function of cleaning the tank.

All plumbing supplies are sold in the store.

Need to know! It is necessary to provide moderate heating in the winter time - aquarium heaters are suitable for such an organization, they will do an excellent job with this task. Need to know! For chickens drinking trough is being built on the same principleas for adult chickens, but the vessel should be smaller.

All types of drinking bowls work on the same system - providing chickens with automatic water supply. The design can be fenced with a cage or left open, but the first option is more convenient. Special financial costs are not required, and the material for the manufacture of the device abound. You can also use fantasy and build a bird feeder with your own hands according to your own preferences.

Plastic Chicken Drinker: Technology

And finally, a few words about how the drinking bowl for chickens is made with its own hands from a pipe - as a rule, a sewage system, with a diameter of at least 100mm. This type of chicken drinker provides a constant change of water, supplying domestic animals with fresh liquid - in principle, it can also be used as a regular trough with standing water. The design of this device is a long, horizontally located cylinder, in the upper part of which there are rectangular slots - so to speak, access to water. On one side of the pipe, a tap is installed with a funnel for supplying liquid, and on the other, an adapter 100 by 50 mm, which serves both to hold water and to drain it. Если в воронку потихоньку, тонкой струйкой, постоянно лить воду, то после наполнения трубы она такой же тонкой струйкой начнет из нее вытекать – это своего рода автоматическая поилка для кур. Естественно, струйку подачи нужно будет отрегулировать так, чтобы обеспечить минимальный расход воды.By and large, if you open the tap every day, then the water in the drinker can be changed in manual mode - as an option, you can do it with a bucket in your hands.

Drinking bowl for chickens from the pipe photo

And in conclusion, the topic of how to make a drinking bowl for chickens with your own hands, it remains to add only one thing - to say that these are not the only constructive solutions that allow providing chickens with life-giving moisture. For example, if we are talking about a chicken aviary, then in general it is possible to dig up a small artificial reservoir, in which water is replenished with a hose. There are a lot of options, in principle, but whatever one may say, they all boil down to the varieties described above - you just need to understand that you can use any more or less suitable materials at hand to make the drinker.

10.15.2018 admin Comments No Comments

Growing chickens at home is a simple matter, but it requires some effort from the farmer. This and the creation of the right conditions of detention, and catering.

This article will discuss how to make troughs and shelves with their own hands. Yes, of course, this inventory can be easily purchased at any hardware store, but in order to save financial resources, as well as to meet individual preferences and design features of chicken coops, it can easily be made independently.

What is suitable as improvised material

If you decide to make feeders for chickens and drinkers with your own hands, then not only new products will be suitable as the source material, but also those that have already been in use.

  • old plastic pipe trim,
  • buckets, troughs,
  • crates
  • plastic bottles,
  • parts of the incubator (which have become unusable in their first use).

What should be the feeder for chickens

Determining the size and appearance of the feeder or drinker, which you will do with your own hands, you need to consider the following points:

  • This inventory must match the age characteristics of chickens and their breed,
  • they must be comfortable to use (chickens are provided with easy access to food and water),
  • the volume of feeders should provide a double supply of food (this applies only to dry feed).

For solid feeds, feeders are made of wooden materials, for wet foods - exclusively plastic or metal.

Hoses, plastic bottles, buckets and other materials can be used to make chicken heaters.

Poultry equipment manufacturing techniques

At each compound always in sufficient quantities, you can find plastic bottles of various sizes. For the manufacture of feeders use only containers from under the food liquids. The optimal volume is a five or six liter bottle. It is necessary to cut off the upper part, and below, departing eight centimeters from the bottom, make holes through which chickens will peck at dry food (grain, deft, mixed feed).

Of the bottles that have handles, you can make and suspended trough on the same principle. Such feeders should be hung at such a distance that chickens can easily reach the food.

Drinkers with their own hands with great success made of plastic pipes. To do this, take two pipes with different diameters and connect them perpendicularly with the aid of a bend. Water is poured into a vertical pipe and is distributed along a horizontal pipe. She, in turn, from the back side is closed with a cap and cut off along the entire length of about half. This design can also be used to supply dry food. It is very ergonomic, takes up little space, and at the same time makes it possible to provide large numbers of chickens at the same time with food and water.

The old plastic bucket, which has become unsuitable for use in the household, but remained intact, can be successfully used as an improvised material for organizing the feeding of chickens.

Making it a trough with your own hands is easy. Small holes are made in the bucket in the upper part; according to the laws of physics, they help to ensure the natural outflow of feed (dry) and water. The bucket itself is turned upside down and placed on a shallow tray or bowl. In order to ensure him a tight fixation, it is fastened with screws.

If this design is used as a drinking trough, then during the cold season, heating is provided so that the water in it does not freeze. With their own hands, the heating is made from ordinary wooden lumber and a light bulb, which is installed under the trough. The water in the bucket is constantly heated and remains warm.

Feeders with their own hands are made from plywood sheets. A small wooden frame is made, which is upholstered with plywood below and on the sides. In the lower part of the received box, holes are made and a feeder is attached to them with small bumpers that prevent the feed from spilling out. Thus, grain or mixed feed is poured into a plywood box with a small margin, and from there it enters small feeders, which are replenished as they empty. For structural strength, all its parts are fastened with screws or screws.

These are the simplest designs that can be made independently from scrap materials and minimal financial costs.

However, you should remember some general rules for their manufacture. First, all materials must be non-toxic and free from residues of industrial products (poisons, oils, gasoline). It is best to use products from food. Secondly, the equipment for chickens should be easy to clean and wash in order to avoid the appearance of pathogenic bacteria there that cause various diseases in poultry. Thirdly, the structures should be comfortable for small chickens and be suitable for adult chickens (for this purpose, their different types are provided).

By the way, to report: the container does not necessarily have to be round; it is possible both rectangular and square. But in these circumstances, the shape of the rim must be appropriate. Legs then it is better to install in the corners.

The design of the superstructure remains the same in all variants. All its dimensions in height are also preserved, despite the fact that they can also vary in width.

The superstructure consists of two C-shaped, directed towards each other racks. In the upper part, rings with an inner diameter slightly larger than a 1.5-liter plastic bottle (reserve capacity) are welded to the racks. Rings are interconnected by a bracket, which is a handle when carrying.

Closer to the bottom of the racks are mounted on the consoles two more rings with a diameter smaller (under the neck cone part of the bottle). The consoles are used so that the centers of the rings attached to one rack are on the same vertical axis. It is fundamentally important to find out the installation height of the lower ring: the edge of the neck of the bottle installed in it must remain at the intended level of water in the supply tank (slightly more than half of its height).

For the whole structure, the same material is used steel wire with a diameter of 7 mm.

At the end of the work the structure is covered with oil paint.

Charging avtopilok as follows. In the supply tank, a little more than half, water is poured. After that, bottles filled with fresh water with swirling caps are installed neck down into the ring holders.

Then the caps are cautiously screwed from the bottles.

A few simple options for do-it-yourself auto-drinkers

Now the auto-drinker is ready for continuous operation, invariably maintaining the specified water level in the supply tank until the bottled water is over.

When using the drinker you need to follow simple rules:

1. Install on a horizontal platform.

For a huge herd it will be necessary, of course, not one, but a pair of auto-drinkers.

Selected by search queries, relevant articles:

How to make bird feeders with your own hands?

Feeder for birds, made by own hands, absolutely surely will appeal to feathered guests (of course, if there is food in it).

And also if you live in a city, ...

Poultry accommodation equipment

Nests and nests for poultry farms and farms are not issued. The launch of the bird cage industry in such ...

Types of garden pruners to care for the site

Greetings to you, dear readers! You will surely agree that on the dacha or backyard garden pruner is one of the main assistants, ...

What specific boxes are suitable for seedlings?

For sowing vegetable and flower crops for seedlings need optimal and ergonomic packaging. The box for seedlings is favorable in front of individual tanks because ...

DIY Chicken Feeder

Do it yourself chickens feeder, this is a proven advice on how to make a feeder convenient for their owner and birds out of scrap materials ....

Birdsong: Health Benefits

The sounds of birds singing enter the auditory territory of the cerebral cortex and excite it. And from it another cortex comes into arousal ....

Ready-made solutions for your chicken coop

PVC Trough

Chicken feeders of traditional constructions have an eternal problem: chickens spill no less grain than they eat. Inefficient use of food is one problem, the second: spilled food remains attract mice and rats. Feeders made of PVC pipes will help to save food and reduce access of rodents to it. Corrugated drainage or sewer pipes are excellent for their manufacture.

Everything is very simple: vertically installed pipes with a rounded outlet at the bottom are filled with food, and are closed with a plug at the top.

After feeding the lid closes and the bottom hole.

How to make drinkers for chickens with your own hands?

The feeders are high enough so that you do not have to worry about contamination of food by sewage. At the same time there is no need to constantly fill up the food in the feeder: the pipe filled to the top will “supply” it itself!

Another version of the “rechargeable” trough is easily made from a plastic bucket and a drinking water tank from a cooler. How this design works, it is clear from the photo.

Nests for layers from buckets and tires

There are many successful and cost-effective designs for laying hens. One of the easiest and most convenient options used by farmers in the US is the nests of 5-gallon (18-20 liters) plastic buckets made from paint or mortars. The buckets are fastened to the bottom of the wall of the chicken house by the bottoms - for this purpose, two holes are made in the bottoms in the shape of a keyhole, by which the sockets are hung on the screw heads. Thus, a simple and easily removable structure is obtained.

But the family of farmers from Colorado used a tractor tire as a nest for hens. It turned out the nest in the "two floors". At the edges of the nests, walls were originally supposed to prevent eggs from falling out, but chickens preferred to nest closer to the middle, so that additional walls were not needed.

Plastic box drinking bowl

Providing clean water to the house is a constant concern for the owner of the house. Everyone who keeps chickens knows how quickly the drinkers become soiled. An excellent variant of the auto-drinker, which does not need constant cleaning, is made of a plastic box with a lid for storing things or toys and a valve for the toilet bowl.

Holes of such diameter are made in the walls of the box so that the chicken can easily stick its head and get access to the water. Through a hole in the end wall a valve is sealed, which is connected to the water supply system. The valve is regulated in such a way that the drinking bowl is filled with water by about three quarters.

At FORUMHOUSE, the contents of chickens, their breeds, variants of the chicken coop are actively discussed.

You may be interested in an article on how to diagnose and treat chicken diseases, and a video on the construction of a designer chicken coop.

Care for chickens, though not difficult, but very important matter. Particular attention should be paid to feeding and watering poultry. And if it is not difficult to make a “dinner table” for our birds, then there may be difficulties with water supplies. If you are one of those who want to make a watering dish for chickens with their own hands, then our article will suit you 100 percent.

How to make a drinker for chickens with their own hands

We will tell the 3 most popular options for creating systems for drinking hens.

To begin with, let us highlight the problems that concern us that we have to solve when watering chickens:

The solution to all these difficulties can be a drinking bowl for chickens, using nipples.

This seemingly complicated structure is actually very easy to assemble on your own. All the necessary materials are not difficult to buy in any store.

Nipple watering systems for chickens have long been popular with Russian farmers. This design is easy to manufacture, does not require large material costs, and most importantly, it copes with its function 100%

Nipple 1800 is suitable for adult chickens, it only works up and down. And for the young, nipple 3600 is more suitable, which works in any direction.

Special nipples for drinkers for chickens. It is not easy to find such, we ordered in the online store for the price of 26 rubles apiece. These are imported, we recommend to take them. We didn’t work with the Russians, after a month of use, they huddled and stopped performing their functions

Such a device we get, of course, you can increase its length or somehow improve it. Please note that in our device water is supplied from through a hose from a water tap, you can also make connections with a canister or other container, as described in the article

That's the whole design! As you can see, nothing complicated. It remains to attach the tank, it is better inside the chicken coop, so that the water does not freeze in winter. If you have an unheated chicken coop, you can put an aquarium heater in the tank when the temperature drops below 00C.

Option with water supply from the tank

But, consider another, simpler version of the nipple drinker

This drinking bowl for smokers with their own hands is very simple. Drill a hole in the cap of a plastic bottle or plastic bottle, again, with a diameter of 9 mm. Screw the nipple in and put the cap back on. Cut the bottom of the bottle and hang it in the hen house. On the cap, we adapt the same drip catcher or micro-cup drinker.

In a plastic bucket or barrel, make holes, tap, cut threads, process threads on nipples with teflon tape and screw them in

We hang the resulting structure and everything is ready, your chickens are not thirsty, and you calmly go about your business

Now, it is possible to process joints with Teflon tape and fill the drinking bowl with water. If one such device is not enough, make a few drinkers, they will not take up much space in the hen house.

Comparing the first and second options nipple drinkers for chickens, we understand that the first design is much more global and efficient, although more difficult to create. So, you decide!

The easiest homemade drinker for chickens

Materials for this drinker can be found in any, even the smallest, household. This is a bucket and a big dish. Oh, and some more rubber pads.

All you need to do:

  1. Fill the bucket with water.
  2. Cover the bucket on top of the dish. You can use the old unnecessary spacing round shape.
  3. Between the dish and the bucket, fit several rubber pads at the same distance (3-4 pieces are enough). They are necessary to ensure minimum water access.
  4. Now, carefully turn the design over so that the pan is under the bucket.

The drinking bowl is ready and can be put in the hen house, on the street and anywhere. The advantages of such a drinker are simplicity, economy and mobility. But, this option, of course, does not solve all the problems.

We hope that today we have provided you with the necessary information to help solve the problems with watering your chickens. Now, it's up to you! We wish you stable luck in housekeeping!

Popular materials on the site

3 types of spice healing herbs for your backyard

Planting Guide and Tips for Lily Care

Beautiful astilba in garden design: planting tips and care instructions

10 rules to help you prepare high-quality compost

How to make supports for climbing roses: 3 of the most reliable and popular options

Hello, dear editors of the site! For many years I have been dreaming of growing tulips on my windowsill.…

Hello, I have a question about the technology for the processing and cultivation of the soil. Tired of digging up ...

Hello! Finally moved to a new home. We have a small courtyard, which I dream to plant ...

Other questions you can see here.